SHIP'S LOG:
Circumstances have conspired together to prevent me from getting up to ABISHAG for the last few days and so I have not had the chance to see if the hatches have leaked. Then again, it hasn't rained so that did not afford me the wetness to check it out. All things seem working for the good.
The house upon which I am sitting and on which I have been working is actually be cared for now by a pro. All of the effort to remove the kitchen floor proved only marginally helpful to the overall work. The care that was exercised in getting the linoleum and the mastic off without damaging the underfloor proved a lot of wasted effort in that the underfloor, unbeknownst to us had to be removed as well. It wasn't suitable for the cement that will be used for the tiles. The pro came in and stated that he would have just ripped it all up in one shot - linoleum, mastic & underfloor. Well, in any event it is all gone and he is currently laying in the cement board, actually screwing it in. Once it is in, he can begin to lay the tile and tomorrow, or after it is sufficiently dry, grout it. It should all be done by Thursday, indeed it has to be as he has another commitment beginning on Friday!
The rains have just started, though at this time it is really more spitting and sprinkles. By later in the day, it will be severe with a serious chance of flooding "in low lying areas - NOAA." Of course, most of the low-lying areas are already flooded and those that aren't are so wet, they can't take any more water. It should be over by Friday, so it will be back to the boat and the work then.
Tuesday, April 29, 2014
Saturday, April 26, 2014
Hatches Are In!
SHIP'S LOG:
It took about 3 hours (1hr/hatch) to set the hatches in place. Not having done this before, I had only videos on YouTube to go on. It really seemed a rather simple process and really it was. You do it in a series of steps and it just goes. Not having worked with butyl caulking before, the first hatch was a real learning experience. It all seemed to go well, though the process disclosed that either the rear hatch is out of square or the aft deck where it is located is. I am not sure which but the butyl tape caulk should take care of the discrepancy. Of course the proof will come when next it rains, which it is doing right now. If the rain doesn't get in, all is well. If not, well I won't worry about it too much and simply re-do it.
It took about 3 hours (1hr/hatch) to set the hatches in place. Not having done this before, I had only videos on YouTube to go on. It really seemed a rather simple process and really it was. You do it in a series of steps and it just goes. Not having worked with butyl caulking before, the first hatch was a real learning experience. It all seemed to go well, though the process disclosed that either the rear hatch is out of square or the aft deck where it is located is. I am not sure which but the butyl tape caulk should take care of the discrepancy. Of course the proof will come when next it rains, which it is doing right now. If the rain doesn't get in, all is well. If not, well I won't worry about it too much and simply re-do it.
Friday, April 25, 2014
It's BBBBBAAAAAAAAAAACK!!!!!!!!
SHIP'S LOG:
Yes, my Ford P.O.S. is finally back and running. After changing all of the filters, one always checks the simplest things first, it became evident that the fuel filter, which after all is 25 years old, gave up the ghost. So now, I can get back to the boatyard and take up again all the work that needs doing.
If all goes well today (a big "IF") I will set all the hatches, caulking and screwed into place. This is a good thing too as we are supposed to get rain tomorrow(Saturday) and most of next week. It will be a good test for the work done. If they leak again, I shall be most distressed.
Once the hatches are set in place, I get to tackle the overhead, which is another reason I want them not to leak. That project is in several stages:
1.) Cut the ceiling panels to a proper, easy to handle size;
2.) Paint the ceiling panels;
3.) Install the needed wooden strips to which the panels will be affixed;
4.) Attach velcro to the panels and the wooden strips in the appropriate places;
5.) Put the ceiling panels back in place.
As you can see, it is rather a simple project, so what could possibly go wrong?
Yes, my Ford P.O.S. is finally back and running. After changing all of the filters, one always checks the simplest things first, it became evident that the fuel filter, which after all is 25 years old, gave up the ghost. So now, I can get back to the boatyard and take up again all the work that needs doing.
If all goes well today (a big "IF") I will set all the hatches, caulking and screwed into place. This is a good thing too as we are supposed to get rain tomorrow(Saturday) and most of next week. It will be a good test for the work done. If they leak again, I shall be most distressed.
Once the hatches are set in place, I get to tackle the overhead, which is another reason I want them not to leak. That project is in several stages:
1.) Cut the ceiling panels to a proper, easy to handle size;
2.) Paint the ceiling panels;
3.) Install the needed wooden strips to which the panels will be affixed;
4.) Attach velcro to the panels and the wooden strips in the appropriate places;
5.) Put the ceiling panels back in place.
As you can see, it is rather a simple project, so what could possibly go wrong?
Thursday, April 17, 2014
And On It Goes!
SHIP'S LOG:
Well, I was able to get a good friend to haul me from Griswold to New London yesterday in time for Red Cross Certification Class at TYC. It was rather unsettling to find that lots of the procedures for First Aid that I struggled so hard to learn as a Boy Scout so many years ago are no longer used. Some are no considered merely a waste of effort and others are now seen as doing actual damage to the person you are trying to help! It was the hope of all of us who were taking the class that we would never have cause to use any of the procedures we learned. Luckily for me, one of my classmates lives close enough to Griswold that it was terribly out of his way to take me home. It would have been one hell of a long walk!
AAA came this morning and picked up the P.O.S. and hauled it away to Stop'N'Go Transmission in Groton. It is not that i suspect that it is a transmission problem, rather that the owner, Joel, is a friend and years ago I performed his wedding. And since he is still happily married, he is still a good friend. He, or one of the guys in his shop, will be able to handle pretty much anything that needs doing and hopefully at a very friendly fee. Considering the money I have got to lay out to get the sails back from the sail-maker and ABISHAG out of the boatyard, I am going to be hard stretched to cover expenses. In a month or so, I will be bringing in a few ducats from running the launch and cleaning the club house at TYC, but that is still in the future. Hopefully, until that time, Publisher's Clearing House will finally find me with their Prize Patrol and help me out at least a little bit.
Well, I was able to get a good friend to haul me from Griswold to New London yesterday in time for Red Cross Certification Class at TYC. It was rather unsettling to find that lots of the procedures for First Aid that I struggled so hard to learn as a Boy Scout so many years ago are no longer used. Some are no considered merely a waste of effort and others are now seen as doing actual damage to the person you are trying to help! It was the hope of all of us who were taking the class that we would never have cause to use any of the procedures we learned. Luckily for me, one of my classmates lives close enough to Griswold that it was terribly out of his way to take me home. It would have been one hell of a long walk!
AAA came this morning and picked up the P.O.S. and hauled it away to Stop'N'Go Transmission in Groton. It is not that i suspect that it is a transmission problem, rather that the owner, Joel, is a friend and years ago I performed his wedding. And since he is still happily married, he is still a good friend. He, or one of the guys in his shop, will be able to handle pretty much anything that needs doing and hopefully at a very friendly fee. Considering the money I have got to lay out to get the sails back from the sail-maker and ABISHAG out of the boatyard, I am going to be hard stretched to cover expenses. In a month or so, I will be bringing in a few ducats from running the launch and cleaning the club house at TYC, but that is still in the future. Hopefully, until that time, Publisher's Clearing House will finally find me with their Prize Patrol and help me out at least a little bit.
Wednesday, April 16, 2014
My P.O.S. is D.O.A.!!!!!!!!!!!!!!!!!!!!!!
SHIP'S LOG:
Did you ever have one of those days? Or weeks? well, this week could be one of those. First of all, it is Holy Week and there is lots of spiritual, church-oriented stuff going on. It is the busiest week of the year for Catholics.
This week also is loaded with meetings for me. Last night I had to attend the initial meeting of the regatta committee for TYC. It is not a favorite committee as it is lots of work and you have to deal with a lot of complaining from racers no matter how much effort you put into the races and no matter how well things go. It is at best a thankless job which is why so few people want to be on the committee. Still it is necessary for the club and so I signed on. In addition to that, there is a Red Cross Certification Meeting/Class that I have to attend tonight and pay $50 for the privilege. It is a necessary part of the Launch Operator's requirements that I need to fulfill. And tomorrow, I have an appointment with the Department of Transportation of the Federal Government to get my TWIC (Transportation Worker's Identification Card), another necessary items for the Launch Operator's Certificate.
And my car died! What exactly the problem is, I don't know. Could be fuel pump, could be distributor, could be ghosts in the machine. In any event, it is not functioning to the point where it is drivable. To make matters worse, I don't have the money to get it towed to a garage where someone can over-charge me for more than the necessary work, let alone pay for the work in the first place.
Right now, I am hunting around for someone to put the arm on to get me a ride down to New London and TYC where the Red Cross Certification Class is being held today.
And I haven't even discussed the work that still needs doing on ABISHAG!!!!!!!!!!!!!!!!!!!!!
Did you ever have one of those days? Or weeks? well, this week could be one of those. First of all, it is Holy Week and there is lots of spiritual, church-oriented stuff going on. It is the busiest week of the year for Catholics.
This week also is loaded with meetings for me. Last night I had to attend the initial meeting of the regatta committee for TYC. It is not a favorite committee as it is lots of work and you have to deal with a lot of complaining from racers no matter how much effort you put into the races and no matter how well things go. It is at best a thankless job which is why so few people want to be on the committee. Still it is necessary for the club and so I signed on. In addition to that, there is a Red Cross Certification Meeting/Class that I have to attend tonight and pay $50 for the privilege. It is a necessary part of the Launch Operator's requirements that I need to fulfill. And tomorrow, I have an appointment with the Department of Transportation of the Federal Government to get my TWIC (Transportation Worker's Identification Card), another necessary items for the Launch Operator's Certificate.
And my car died! What exactly the problem is, I don't know. Could be fuel pump, could be distributor, could be ghosts in the machine. In any event, it is not functioning to the point where it is drivable. To make matters worse, I don't have the money to get it towed to a garage where someone can over-charge me for more than the necessary work, let alone pay for the work in the first place.
Right now, I am hunting around for someone to put the arm on to get me a ride down to New London and TYC where the Red Cross Certification Class is being held today.
And I haven't even discussed the work that still needs doing on ABISHAG!!!!!!!!!!!!!!!!!!!!!
Friday, April 11, 2014
Work! Work! Work! Work!
SHIP'S LOG:
It can be such fun to destroy stuff! And this week, there was plenty of that. But all this "destruction" was actually the necessary first step to doing the needed work and projects. The three hatches original to the construction of ABISHAG got popped out and I was disappointed. Without an inward flange, they were simply flush fitted and even more distressing was the fact that they were secured simply with machine screws and the mastic. The machine screws kept them from shifting horizontally and the mastic kept them from moving vertically. And while they did technically "stay in place" over the years, they did move at least a little and so began to leak. They had been set on a reinforced lip of wood covered with fiberglass, but the movement compromised the mastic and water got in and the wood below the fiberglass and it began to rot. Obviously this problem was discovered prior to my acquiring ABISAHG because sections of the rotted wood had been remove and the void filled with epoxy. Strangely, all the wet wood was not removed at the time of the previous repair and so the wood that remain eventually began to rot and I pulled out the remaining sections for the main hatch lip. I will filled and fair it with epoxy . . . after I buy the epoxy and after I check out the lips on the other two hatches. There is no reason to expect that they have escaped the rot as both also leak.
The interior overhead in the saloon and galley has been removed. The four (4) panels will become eight (8) when they are reinstalled. While they were installed with screws originally, they will be reinstalled with Velcro so that the panels can more easily be removed. That will be a good things as there are somewhere close to 100 screws holding the panels in place and that is not even counting those that held the aft cabin panels in place. They are down too. And it is a good thing too. It is amazing, as I took the panels down, how much condensation coated the underside of the deck. It was soaking wet, with huge drops of water everywhere. Of course, a boat which spends so much of its time on the water in the hot summer, collects a lot of humidity which eventually has to condense sometime. Having the boat overhead panels so easy to remove will make it possible to take them down in the fall when the boat goes up for storage, making the condensation easier to prevent, or at least as much as possible. I also had to hit a lot of spots with bleach to kill off the black mold, another downside from all the condensation. I'll have to acquire 100 feet or so of 2" x 1/2 " of wood to set in the ceiling to which the panels will be "Velcro-ed" in place. It is not a particularly difficult job, it will be labor intensive though.
I am taking the day off today. The weather is "iffy," plus i "hurt" in places I didn't know I had. Perhaps I am getting old.
It can be such fun to destroy stuff! And this week, there was plenty of that. But all this "destruction" was actually the necessary first step to doing the needed work and projects. The three hatches original to the construction of ABISHAG got popped out and I was disappointed. Without an inward flange, they were simply flush fitted and even more distressing was the fact that they were secured simply with machine screws and the mastic. The machine screws kept them from shifting horizontally and the mastic kept them from moving vertically. And while they did technically "stay in place" over the years, they did move at least a little and so began to leak. They had been set on a reinforced lip of wood covered with fiberglass, but the movement compromised the mastic and water got in and the wood below the fiberglass and it began to rot. Obviously this problem was discovered prior to my acquiring ABISAHG because sections of the rotted wood had been remove and the void filled with epoxy. Strangely, all the wet wood was not removed at the time of the previous repair and so the wood that remain eventually began to rot and I pulled out the remaining sections for the main hatch lip. I will filled and fair it with epoxy . . . after I buy the epoxy and after I check out the lips on the other two hatches. There is no reason to expect that they have escaped the rot as both also leak.
The interior overhead in the saloon and galley has been removed. The four (4) panels will become eight (8) when they are reinstalled. While they were installed with screws originally, they will be reinstalled with Velcro so that the panels can more easily be removed. That will be a good things as there are somewhere close to 100 screws holding the panels in place and that is not even counting those that held the aft cabin panels in place. They are down too. And it is a good thing too. It is amazing, as I took the panels down, how much condensation coated the underside of the deck. It was soaking wet, with huge drops of water everywhere. Of course, a boat which spends so much of its time on the water in the hot summer, collects a lot of humidity which eventually has to condense sometime. Having the boat overhead panels so easy to remove will make it possible to take them down in the fall when the boat goes up for storage, making the condensation easier to prevent, or at least as much as possible. I also had to hit a lot of spots with bleach to kill off the black mold, another downside from all the condensation. I'll have to acquire 100 feet or so of 2" x 1/2 " of wood to set in the ceiling to which the panels will be "Velcro-ed" in place. It is not a particularly difficult job, it will be labor intensive though.
I am taking the day off today. The weather is "iffy," plus i "hurt" in places I didn't know I had. Perhaps I am getting old.
Tuesday, April 8, 2014
Hatching
SHIP'S LOG:
I pulled the two of the three hatches that have been leaking. I figured that after years of trying to find the leaks and plug them in what could best be called a "half-assed manner," I decided to pull the hatches and completely repair whatever needed to be repaired and then caulk the hell out of them before I put them back. The problem was that I couldn't figure out how to remove the interior trim so that I could get at the nuts on the bottom of the hatch bolts. The trim looked as though it was glassed in place, so I took a chance to see if I could unscrew the bolts without securing the nuts. Imagine my surprise when the bolts all came out with minimum effort. It turns out that the hatches were secured simply by screwing the bolts into the fiberglass lip beneath the hatches.There were no securing nuts at all! In addition, the was no "L"-shaped flange extending into the hatch opening. Evidently, the hatch was placed on the hatch opening after it had been caulked and then simply screwed into placed. No wonder the bloody thing leaked after 34 years of deck flexing. I can't add the "l" shaped flange so it will have to be set back in place pretty much as it was originally.
The couple from Maine called at the last minute to cancel the visit, They were going skiing one last time. I can't tell if that is true or they were using it as an excuse not to come and look at ABISHAG. It could be that they decided that they don't want her but they felt uncomfortable saying so. It happens all the time. I know they didn't find a better deal on "a sister ship" as the only other CN 39 (there's only three in the the US) for sale in down in the Chesapeake and they want $62,000. They probably found an other deal and weren't all that committed to stay in the Camper Nicholson Family as they originally claimed. O well, such is life.
I pulled the two of the three hatches that have been leaking. I figured that after years of trying to find the leaks and plug them in what could best be called a "half-assed manner," I decided to pull the hatches and completely repair whatever needed to be repaired and then caulk the hell out of them before I put them back. The problem was that I couldn't figure out how to remove the interior trim so that I could get at the nuts on the bottom of the hatch bolts. The trim looked as though it was glassed in place, so I took a chance to see if I could unscrew the bolts without securing the nuts. Imagine my surprise when the bolts all came out with minimum effort. It turns out that the hatches were secured simply by screwing the bolts into the fiberglass lip beneath the hatches.There were no securing nuts at all! In addition, the was no "L"-shaped flange extending into the hatch opening. Evidently, the hatch was placed on the hatch opening after it had been caulked and then simply screwed into placed. No wonder the bloody thing leaked after 34 years of deck flexing. I can't add the "l" shaped flange so it will have to be set back in place pretty much as it was originally.
The couple from Maine called at the last minute to cancel the visit, They were going skiing one last time. I can't tell if that is true or they were using it as an excuse not to come and look at ABISHAG. It could be that they decided that they don't want her but they felt uncomfortable saying so. It happens all the time. I know they didn't find a better deal on "a sister ship" as the only other CN 39 (there's only three in the the US) for sale in down in the Chesapeake and they want $62,000. They probably found an other deal and weren't all that committed to stay in the Camper Nicholson Family as they originally claimed. O well, such is life.
Subscribe to:
Posts (Atom)
